• Steam recently changed the default privacy settings for all users. This may impact tracking. Ensure your profile has the correct settings by following the guide on our forums.

M3.80 downgrade Problem

S

squid

New Member
I have a big PSP Phat problem... I am stuck with a partial brick. I can get into recovery menu however if I flash 1 and reset, i get a brick.


It all started when I updated m3.80 to m3.80-2 then installed 1.5 addon for 3.80. After installing the 1.5 - 3.80 addon none of my ISO's would start. So, I ran DC3 and reinstalled 3.71. Now I am screwed... bad block on 890. I cannot get out of loop of blannk XMB...


PLEASE HELP!
 
squid said:
I have a big PSP Phat problem... I am stuck with a partial brick. I can get into recovery menu however if I flash 1 and reset, i get a brick.


It all started when I updated m3.80 to m3.80-2 then installed 1.5 addon for 3.80. After installing the 1.5 - 3.80 addon none of my ISO's would start. So, I ran DC3 and reinstalled 3.71. Now I am screwed... bad block on 890. I cannot get out of loop of blannk XMB...


PLEASE HELP!
Click to expand...

Did you try running DC3 again? Perhaps something went wrong while flashing.
 
x3sphere said:
Did you try running DC3 again? Perhaps something went wrong while flashing.
Click to expand...

Yes, over and over agian. DC3 states succesful install, and press X to shutdown. Once I reboot, it goes into a green XMB screen that is blank other than the battery icon.

I have tried to delete my config file under flash 1 and I get a brick. I repeat the DC3 process and try to format flash1 and reset from the M33 recovery menu, I get the Bluescreen of death (corrupt settings - press O)

I am stuck in this loop...
 
squid said:
Yes, over and over agian. DC3 states succesful install, and press X to shutdown. Once I reboot, it goes into a green XMB screen that is blank other than the battery icon.

I have tried to delete my config file under flash 1 and I get a brick. I repeat the DC3 process and try to format flash1 and reset from the M33 recovery menu, I get the Bluescreen of death (corrupt settings - press O)

I am stuck in this loop...
Click to expand...

Try doing this. Enter recovery mode and access flash1 through USB. Delete everything on flash1, even the folders.

Then exit recovery mode and the PSP should boot up to a blue screen again. From here follow the prompt to restore and it should enter the XMB.
 
380 psp slim

I'm newbie here. I have psp slim with 3.80 sony original firmware. Can I use the pandora battery to mod to 3.71 m33 rev 2??? My friend got pandora battery. Just want to ask U first before I flash using the battery. Just afraid that it will brick my psp. Anyway just want to whether can we use the pandora battery also if i'm using psp original firmware 4.0....Thanks... :mellow:
 
itchigo777 said:
I'm newbie here. I have psp slim with 3.80 sony original firmware. Can I use the pandora battery to mod to 3.71 m33 rev 2??? My friend got pandora battery. Just want to ask U first before I flash using the battery. Just afraid that it will brick my psp. Anyway just want to whether can we use the pandora battery also if i'm using psp original firmware 4.0....Thanks... :mellow:
Click to expand...



Sure you can. :D

4.0? Are you serious? I though the newest was 3.80.. How'd you get 4.0?:confused1:

Also, if you have a question in the future, open a new thread. ;)
 
Acerthief said:
Sure you can. :D

4.0? Are you serious? I though the newest was 3.80.. How'd you get 4.0?:confused1:

Also, if you have a question in the future, open a new thread. ;)
Click to expand...


Thanks bro. I'm not using 4.0 yet. The firmware is not out yet. Sorry to make u confuse..:laugh: I just asking whether if sony comes with 4.0 later, will it be able to use pandora battery.
 
You must log in or register to reply here.
Back
Top